search

Robertshaw 9820I Manual de usuario

Busca en linea o descarga Manual de usuario para Panel De Control Robertshaw 9820I. Robertshaw 9820I User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 2
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Models
9801
i
,
9815
i
and
9820
i
Quick Start Installation Manual
111-321D
Installation DOs and DON’Ts
DO
• Shut off all power to system before installing.
• Read entire manual before installing.
• Make sure that all wiring conforms to
national and local codes.
DO NOT
•
Install on voltages greater than 30 VAC.
• Short jumper across terminals on the gas
valve or at the system control.
• Connect ground to any terminal in
this unit.
• Install on outside walls or in direct sunlight.
Select location for installation.
1
Open the case with a screwdriver. Place
in slot and gently pry forward at all four
locations.
2
Mark mounting hole locations on wall.
3
Drill
3
/
16
” holes at marked locations on
wall. Insert plastic anchors into holes.
4
Align unit base over plastic anchors
embedded in wall and secure with the
screws provided.
5
Connect wiring between unit and
furnace. For Model 9801i (1H/1C
furnace applications).
6
Cut
out
opening
a
b
1/4"
1-1/2"
1"
1
2
3
4
Mark mounting hole
locations on wall using
unit base as template.
Drill
3
/
16
holes
a
b
Press anchors into holes until flush.
Y1
R
C
E/W1
H O B G
Thermostat
C - 24VAC Common
R - 24VAC
Y1 - 1st stage cooling
E/W1 - 1st stage heating
O - Not used
B - Not used
G - Fan
H - Humidification
TERMINAL DESIGNATIONS
C
C
H
R
Y
W
G
B
O
Note: To avoid electrical problems, use the system transformer for both
the thermostat and humidifier.
9801i
Humidifier
Equipment Wiring
Terminals
Please refer to furnace
installation manual for
proper terminations
Remove 1/4” of insulation
from end of each wire
DELUXE
PROGRAMMABLE
THERMOSTATS
Vista de pagina 0
1 2

Indice de contenidos

Pagina 1 - 1-1/2"

Models 9801i, 9815iand 9820iQuick Start Installation Manual111-321DInstallation DOs and DON’TsDO• Shut off all power to system before installing.• Rea

Pagina 2 - Recycling Thermostat

NOTE: For 9801i single stage heatpump applications, place a jumperbetween the E/W1 and Y1 terminals.7Connect wiring between unit and furnace. For Mode

Modelos relacionados 9815I | 9801I |

Comentarios a estos manuales

Sin comentarios
  • Aj-antunes-co Bisley Cricket OJ Electronics Lintex
  • Interlogix Los Componentes Del Dispositivo De Seguridad Jensen Receptores de medios de coches Logitech Relojes de alarma CycleOps Bicicletas Asus Discos duros internos
  • Bosch KGS 39X48 Hampton Bay 03237-4 Roland CD-2 Dell PowerEdge 2500 Nikon D60
  • Samsung CTR264KC01 Manual de usuario Kenwood UD-900M Manual de usuario LG 43LF570T Manual de usuario Sony KD-55XD8005 Manual de usuario Samsung SHR-7080 Manual de usuario